The Replacement Rubber Cap # 37262105 is designed to fit over a brass city water inlet like the RV City Water Inlet # 372321-B-36-A. The notch in the rubber cap will only allow for a limited amount of room to fit over the city water inlet.
If you have an inlet like the RV City Water Inlet # 372160-85-A-26A you will not be able to fit the cap over the inlet. The plastic is affixed to where it cannot be removed from the inlet. You can attach the cap by drilling a small hole into the strap... view full answer...
We have a city water inlet with a 1/2" FPT that is very close to what you are describing, but the flange is slightly smaller, so it isn't exact. I did want to mention it just in case it turns out you are able to use them. Each of the following inlets have a 1/2" FPT, 2-7/8" flange outer diameter, and measure 1-5/8" from the back of the flange to the end of the valve:
- RV City Water Inlet w/ Brass Check Valve - 1/2" FPT - Plastic Flange # 37262135
- RV City Water Inlet w/ Brass Check... view full answer...
The Valterra Water Inlet for RVs # A01-0178LFVP does not have a pressure regulator so you would need to purchase one like the # A01-1124VP separately if you wanted regulate the pressure running to your RV. This water inlet does have a check valve though to prevent water from backfeeding. This pressure regulator with screw into the outside of this inlet and allow you to screw on your fresh water hose. view full answer...
While we do have replacement water hatch inlets available (but not gas hatches), there are none for specific RVs so we wouldn't know if they are the same as newer models. In order to determine the correct water inlet you just need to know your water line and cut out size.
For example, if it was a city water inlet and you had a 1/2" MPT tank connection and your cut out was 5-7/8" wide x 4-3/4" high you would use the Valterra City Water Inlet and Lockable Hatch for RVs # A01-2004VP.
I... view full answer...
The Dometic 310 Part-Timer RV Toilet # DOM57FR water inlet is a 1/2" NPT fitting. You should be able to easily find a tee to connect to the water supply line and water inlet on the toilet, just make sure you determine the bidet's fitting size before you go get a tee and find out it's the wrong size. view full answer...
I contacted the manufacturer and they were able to confirm that the Replacement Plug and Strap for Valterra RV City Water Inlet # T1020-1EVP does have 3/4" garden hose threads on it. view full answer...
We have a direct replacement for your OEM 12-volt Shurflo 2088-422-144 fresh water pump with HydroMax RV Fresh Water Pump # P25201 which uses the same inlet and outlet size you have now and has pressure and output specs as well. This has 1/2 inch diameter hose fittings at the inlet and outlet that is designed to work with a tapered watertight seal. view full answer...
The Valterra Water Inlet for RVs part # A01-0176LFVP is universal, not vehicle specific so it should fit your motorhome though it may also require some small modifications. I have attached a few photos for you below which lists some of the dimensions that will be needed for determining compatibility.
I also have attached a full list of our other water inlets for you to look through. view full answer...
The Valterra # RF911BK water inlet features a barbed connection that starts out at 1-1/4 inches in diameter at the end and flares to 1-3/8 at the end right behind the inlet. It will fit a flexible hose with a 1-1/4 inch inside diameter. If you're needing the hose to connect the inlet and the tank, use # CAM36601. view full answer...
The Valterra Dual RV Water Inlets # A01-2001VP is going to be the closest thing we have to fitting your cutout area, so your best bet is to make your cutout a little larger to accommodate this fitment.
Aside from that, everything else available is a standalone inlet with a circular cutout installation that isn't even close to what you're needing. view full answer...
The Valterra Lockable Dual RV Water Inlets # A01-2000VP is very similar in size but without knowing the actual cutout hole dimensions it's not possible to know if you'll need to make modifications. This dual inlet box requires a 5-7/8" wide x 4-3/4" tall cutout hole.
Worst case scenario you would have to trim the cutout hole a bit larger to fit this new inlet box in place. You'll want to use butyl tape # AL28FJ on the mounting flange and non-sag sealant # 344270341437-1 around the outer... view full answer...
Yes, the Replacement Cap and Strap for Valterra RV Gravity Fill Water Inlet # A0120SBKVP will work with 1-1/2" pipe threads.
This cap is a universal part and will fit on just about any quarter turn gravity fill inlets. view full answer...
Unfortunately, I don't have any information as to what fitting is on the city water inlet of your 5th wheel trailer. However, you should be able to use either the Camco Quick Hose Connect part # CAM20143 or the Camco Quick Hose Connect part # CAM20135.
If not can you please send me a photo of your water inlet and I would be glad to see if we have any options for you. view full answer...
The inlet and discharge threading on the Flow Max RV Fresh Water Pump - 12 Volt # LC689052 is .825 inches using a digital caliper so it is not the 1/2 inch male national pipe thread which would be .840 inches. Lippert recommends using the barb fittings included and using 1/2 inch inner diameter flexible hose. My contact said they use the odd size to protect the pump from over-tightening and possible cracking of the housing. The fittings are designed to only be hand tight. view full answer...
Yes. Dump station inlets are a common size and the Camco RV Gray-Water Drain Adapter and seal # CAM39322 will fit. I have linked a video review of this product for you. view full answer...
For your 2018 Keystone Bullet, I don't know what cutout dimension is behind the 7-1/2 by 5-1/4 inch mounting of the # A01-2001VP. The lockable cover that replaces this is the Valterra City Water Inlet and Lockable Hatch for RVs - Plastic - White - Gravity Fill # A01-2004VP. This system has overall dimensions of 7-5/8" wide x 6-1/2" high but it only requires a cutout of 5-7/8 inches by 4-3/4 inches so enlarging the opening may not be necessary. view full answer...
Faucets typically either have a 3/8 or 1/2 water inlet. The RV Bathroom Faucet - Dual Knob Handle - Parchment Item # 277-000042 is a 1/2" water inlet so you'll just want to measure the inner diameter of your current faucet to make sure it's the same size. view full answer...
We carry inline filters like the AquaFresh Interior Inline Replacement Water Filter w/ 1/2" Fittings - GAC/KDF - 20 Micron # AF24FR that you could place inline with your cold water line. It has 1/2" threaded fittings so you may need some adapters depending on the size of your current fittings.
We also carry larger water filter systems that use replaceable cartridges like the Clearsource Premier RV Water Filter System # CS77FR. These typically get mounted in a storage bay and hooked into... view full answer...
The Ultra Faucets RV Drinking Water Faucet part # 277-000189 has an inlet shank of 2-1/4" but once all the hardware is installed you are right at 1-1/2" so it will be a tight fit. You may need to drill out a recess to make sure the hardware threads but I recommend to dry fit it without doing that first. Just drop the inlet shank with the base and hand tighten the hardware. If you can't tighten them you will need to make a small recess. view full answer...
The RV Shower Panel # WAY72YR uses standard connection sizes to hook up to the existing water inlets for your shower and the body of the panel is 51" Tall x 5-5/8" Wide to cover up the holes left by your old shower faucet. To confirm that 5-5/8" is wide enough you can pop off your old faucet handles and measure the hole spacing. view full answer...
Go To Results